收藏本站
W972GG6JB
Notes:
1. All voltages are referenced to V SS .
2. Tests for AC timing, I DD , and electrical AC and DC characteristics may be conducted at nominal reference/supply voltage
levels, but the related specifications and device operation are guaranteed for the full voltage range specified. ODT is
disabled for all measurements that are not ODT-specific.
3. AC timing reference load:
VDDQ
DQ
Output
DUT
DQS, DQS
Figure 16
Timing
25 Ω
reference
point
– AC timing reference load
VTT = VDDQ/2
4. This is a minimum requirement. Minimum read to precharge timing is AL + BL / 2 provided that the tRTP and tRAS(min)
have been satisfied.
5. If refresh timing is violated, data corruption may occur and the data must be re-written with valid data before a valid READ
can be executed.
6. This is an optional feature. For detailed information, please refer to “operating temperature condition” section 9.2 in this data
sheet.
7. tCKE min of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the
valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not
transition from its valid level during the time period of tIS + 2 x tCK + tIH.
8. A minimum of two clocks (2 * nCK) is required irrespective of operating frequency.
9. tWTR is at least two clocks (2 * nCK) independent of operation frequency.
10. There are two sets of values listed for Command/Address input setup time: tIS(base) and tIS(ref). The tIS(ref) value (for
reference only) is equivalent to the baseline value of tIS(base) at VREF when the slew rate is 1.0 V/nS. The baseline value
tIS(base) is the JEDEC defined value, referenced from the input signal crossing at the VIH(ac) level for a rising signal and
VIL(ac) for a falling signal applied to the device under test. See Figure 17. If the Command/Address slew rate is not equal to
1.0 V/nS, then the baseline values must be derated by adding the values from table of tIS/tIH derating values for DDR2-667,
DDR2-800 and DDR2-1066 (page 55).
CLK
CLK
t IS(base) t IH(base)
t IS(base) t IH(base)
Logic levels
V DDQ
V IH(ac) min
V IH(dc) min
V REF(dc)
V IL(dc) max
V IL(ac) max
V SS
V REF levels
t IS(ref)
t IH(ref)
t IS(ref)
t IH(ref)
Figure 17
– Differential input waveform timing – tIS and tIH
Publication Release Date: Nov. 29, 2011
- 47 -
Revision A02
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
W9751G6IB-25 IC DDR2-800 SDRAM 512MB 84-WBGA
W9751G6KB-25 IC DDR2 SDRAM 512MBIT 84WBGA
W9812G6JH-6I IC SDRAM 128MBIT 54TSOPII
W9816G6IH-6I IC SDRAM 16MBIT 50TSOPII
W9825G6JH-6I IC SDRAM 256MBIT 54TSOPII
W9864G6JH-6I IC SDRAM 64MBIT 54TSOPII
WM-5614 CABINET WALL MOUNT 37.25X17.9"
WRR-2244 RACK WALL MOUNT RELAY 42" X 19"
相关代理商/技术参数
W972GG8JB 制造商:WINBOND 制造商全称:Winbond 功能描述:32M ??′ 8 BANKS ??′ 8 BIT DDR2 SDRAM
W972GG8JB-18 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 1.875NS BGA
W972GG8JB-25 制造商:Winbond Electronics Corp 功能描述:2GMB DDRII 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 2.5NS 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 2.5NS 60WBGA
W972GG8JB-25I 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 2.5NS 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 2.5NS 80WBGA
W972GG8JB-3 制造商:Winbond Electronics Corp 功能描述:DRAM Chip DDR2 SDRAM 2G-Bit 256Mx8 1.8V 60-Pin WBGA 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 3NS
W9751G6IB-25 功能描述:IC DDR2-800 SDRAM 512MB 84-WBGA RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-MFP 包装:带卷 (TR)
W9751G6JB 制造商:WINBOND 制造商全称:Winbond 功能描述:8M ? 4 BANKS ? 16 BIT DDR2 SDRAM
W9751G6JB-25 制造商:Winbond Electronics Corp 功能描述:512GB DDRII